KEMPER Connect IoT Kit
Connect PLC-controlled filter units
The KEMPER Connect IoT Kit connects KEMPER filter units with a PLC controller to KEMPER Connect, such as WeldFil, VacuFil 2000/4000, or KemJet. You see filter condition, compressed air, and when service is due remotely. The unit can be started, stopped, and integrated into automation.

The principle
Like the Bridge, only for PLC units
The IoT Kit is the counterpart to the KEMPER Connect Bridge for filter units with their own PLC, a programmable logic controller. What differs is the interface to the unit and the registration with a PIN code.
Connected to the unit controller
The IoT Kit is connected to the PLC of the filter unit. The Bridge uses the machine cable for this.
Connected via cellular
The operating data goes to KEMPER Connect via cellular. The SIM card is included; your company network is not touched.
The unit is detected
You register the kit like a regular KEMPER device with serial number and PIN code. It detects the connected unit, which then appears under its machine name with the matching dashboard.
Go to setupVariants
For existing and new units
The IoT Kit is available as a retrofit kit for existing filter units and as an accessory for new units, fitted at the factory.
- Retrofit kit for existing KEMPER filter units with a PLC, built in 2018 or later (item no. 3606276)
- For new filter units, fitted at the factory and selected when the unit is configured (item no. 3605623001)

Compatible units
These units can be connected
The IoT Kit connects the following KEMPER filter units. Each appears in KEMPER Connect under its machine name, with dashboard, history, and remote control.





The dashboard
Condition, compressed air, and service on one page
At the top: unit status with start and stop, filter condition, compressed air, and the operating hours until the next service. Below, the filter pressure history shows the last 24 hours with operating state and filter cleanings.

What a unit on the IoT Kit can do
Monitor, maintain, switch, automate
Filter condition
Differential pressure of the filter cartridges as a measure of the filter load, plus the number of filter cleanings.
Compressed air and temperature
Supply pressure for the automatic filter cleaning and temperature of the filter unit.
Service countdown
Operating hours until the next service, on the dashboard and on the service page of the site.
Status and error code
Running or stopped, plus the PLC status code and the error code of the controller.
Electrical status
Four status signals as on/off indicators: contactor feedback, motor protection relay, external on/off, phase sequence monitoring.
History and CSV export
Filter pressure and operating state over 24 hours; temperature and pressure history by day and week, the readings as a CSV file.
Remote start and remote stop
Start and stop the unit from KEMPER Connect, with a safety prompt and feedback.
Rule Engine, schedules, automation
Together with AirWatch, the Rule Engine switches the unit on and off according to the measured air quality. Schedules and simple automation list it under its machine name.
Terms
- PLC
- Programmable logic controller: the industrial computer that controls a unit. The IoT Kit is connected to the PLC of the filter unit.
- Differential pressure
- Pressure difference upstream and downstream of the filter cartridges. It rises as more dust collects in the filter and thus shows the filter load.
- Filter cleaning
- The unit uses compressed air to remove the dust from the filter cartridges. This requires a compressed air supply, typically 5 to 6 bar.
- Contactor feedback
- Reports whether the contactor, the electrical switch of the motor, has actually switched.
- Motor protection relay
- Protects the motor from overload and switches it off when the current is too high.
- Phase sequence monitoring
- Checks whether the three phases of the power supply are connected correctly so that the motor turns in the right direction.
Good to know
For units on the IoT Kit, KEMPER Connect shows errors as the code of the controller. Error and warning codes in plain language are available for the extraction and filter units with native connection or Bridge.
The kit transmits as long as the controller of the unit is powered. After a longer standstill, the dashboard therefore shows the last known values.
Extraction and filter units such as VacuFil Compact, MaxiFil Clean, or AirDome connect through the KEMPER Connect Bridge.
Which filter units do you have?
We check with you which units can be connected through the IoT Kit and show you the dashboards.